Wood-grain cabinets · Codes Y · YU
Wood-grain Cabinets Kampala — Warm Wood Finishes
Luxfit offers warm wood-grain finishes for Kampala kitchens and wardrobes, from pale oak and ash tones to deep walnut and espresso, carefully matched when a wood look is the brief. Structural cores follow the published mix: E1 11-layer plywood for wet zones and stone loads, particle board for tall wardrobe doors and MDF for painted or carved faces. Designed by Ugandans for Ugandans. Visit our Kampala showroom to compare real samples before you lock the quotation.
Why wood-grain
Why choose wood-grain cabinets?
Warm, natural look
Wood-grain finishes bring the warmth of timber to modern kitchens and bedrooms.
Stable cores
Engineered cores are specified by use, so doors and carcases stay flat and true.
Easy care
The fused surface resists scratches and moisture and wipes clean with a damp cloth.
Matched across rooms
Use the same wood-grain code on kitchen units, wardrobes and wall panels for a whole-home look.
Healthier boards
E0 particle board and E1 11-layer plywood; flagship builds use ENF-grade boards with MDI adhesive.
Compare real samples
Wood tones read differently in daylight. See the physical samples at our showroom before you decide.
Wood tones
Wood-grain tones: pale oak to deep walnut
Each wood-grain finish has a Y or YU code. Open a tone below to see it in a 3D room, or browse them all in Finishes & 3D Rooms.
Design Gallery
Wood-grain kitchens & wardrobes
Each design visual opens in our Design Gallery with its layout, finishes and key features.
Specification
Wood-grain cabinet specification
Typical specification
- Finish
- Wood-grain melamine (Y and YU codes)
- Carcase
- E0 particle board; E1 11-layer plywood for wet zones and stone loads
- Tall doors
- High-density particle board up to 2.7 m
- Edges
- Matching edge banding
- Hardware
- Soft-close hinges and runners
Compare
- vs wood veneer
- Veneer is a thin slice of real timber with natural grain; wood-grain melamine is harder and easier to maintain
- vs lacquer
- Lacquer gives a smooth, deep painted colour
- Real timber faces
- See wood veneer cabinets
Indicative budgets
- Indicative kitchen budgets: about UGX 5–12 million (small), 12–25 million (medium) and 25–50 million (large), including cabinetry materials and countertops; appliances are not included. Final quotes depend on layout, finishes and site conditions after measurement.
Cabinet quality control system
Quality control, checked at every stage
Every Luxfit order goes through one quality system, run by Luxfit and our manufacturing partners. Your confirmed drawings feed the production system directly, every panel is labelled and tracked from cutting to packing, and checks are built into each stage rather than left to the end.
- 01
Site measure & confirmed drawings
Our technical team measures on site. Production only starts after you approve the 2D drawings and 3D mock-ups.
- 02
Incoming material inspection
Boards, edge banding and finishes are checked against your specification (board grade, E0 or E1, and finish code) before cutting.
- 03
Smart cutting & edge banding
Production data goes straight from your drawings to the CNC line. Panels are cut to 0.1 mm tolerance and each one gets a QR-coded label.
- 04
Drilling & sorting checks
Each panel is scanned before drilling, so holes follow the drawing and a wrong size or position is flagged. Sorting confirms no part is missing.
- 05
Finished-panel inspection
Inspectors check panel sizes, edge banding, colour and drill positions, then clean every panel so no dust remains before packing.
- 06
Hardware checks
Hinges, runners and fittings are picked by type and quantity for your order, then scanned and photo-checked.
- 07
Packing & dispatch
Packages are scanned to confirm quantities, clearly labelled and tracked in the warehouse until loading.
- 08
Fitting to your drawings
After shipping and Uganda clearance, our team fits your cabinets on site to your confirmed drawings.
Testing standards
Standards we build to
- Formaldehyde
- E0 particle board · E1 11-layer plywood · ENF-grade (≤0.025 mg/m³) on flagship builds
- Adhesive
- MDI medical-grade adhesive: waterproof, no toxic glues
- Machining
- CNC to 0.1 mm tolerance
- Lacquer
- Sprayed in layers and baked (oven-cured)
- Coatings
- Anti-fingerprint, scratch-resistant, UV-yellowing resistant (where specified)
- Hardware
- Soft-close hinges and runners; SUS304 stainless steel fittings; runners and lift mechanisms cycle-tested
- Order accuracy
- QR-coded panels scanned at cutting, drilling, sorting and packing
Board grades, finish codes and hardware are confirmed on your quotation.
Premium cabinets quality assurance
Quality partners behind every Luxfit cabinet
We work with established manufacturing and hardware partners and specify each component by use. The options below are confirmed on your quotation.
Partner factory
Automated production line
CNC cutting, edge banding and drilling on an automated line, for consistent quality and efficient production.
Hardware partner
Blum hinges & runners
Our premium hardware option: smooth, quiet soft-close movement for doors and drawers.
Hardware partner
DTC soft-close hinges
Our standard soft-closing hinges for base units, wall units and tall doors.
Storage fittings
Pull-outs & organisers
Pull-out baskets, organiser drawers and soft-close waste sorters (including HIGOLD) in SUS304 stainless steel and nano-coated aluminium.
Finish
Baked lacquer
L-code lacquer is sprayed in layers and oven-baked, like the paint on premium cars, for a smooth, deep, durable colour.
Boards
Healthier board system
E0 particle board, E1 11-layer plywood and ENF-grade flagship boards, bonded with MDI adhesive.
How it works
How it works: from floor plan to fitting
Payment follows 10% before 2D/3D → 40% before production → 40% before Uganda clearance → 10% after fitting. Full stages are in our guide to lead time for Kampala kitchens and wardrobes.
- 01
Share your plan
Send your inquiry with a floor plan or photos to our sales team.
- 02
Site measure
Our technical team measures on site so the drawings match the real space.
- 03
2D & 3D design
After the 10% design deposit you receive 2D drawings and 3D mock-ups, with three revisions included.
- 04
Production
You confirm the design and pay 40% before production. Production takes about 20–40 days.
- 05
Shipping & clearance
Shipping takes about 28–40 days. 40% is due before Uganda clearance.
- 06
Fitting
Our team fits your cabinets on site. The final 10% is paid after fitting.
Explore
More cabinet materials & finishes
FAQ
Wood-grain cabinets: frequently asked questions
Are wood-grain cabinets made of solid timber?
No. Our wood-grain cabinets use wood-grain melamine finishes (Y and YU codes) on stable engineered cores: E0 particle board, E1 11-layer plywood or particle board, specified by use. For real timber faces, see our wood veneer cabinets.
Which wood tones are available?
From pale oak and ash to warm walnut, smoked walnut and espresso. Browse the codes in Finishes & 3D Rooms and compare the physical samples at our showroom.
Can my kitchen and wardrobes match?
Yes. The same wood-grain code can be used on kitchen units, wardrobes and wall panels for a coordinated, whole-home look.
How do I clean wood-grain cabinets?
Wipe with a damp cloth and mild soap. Avoid abrasive scrubbers. No oiling or waxing is needed.
How long does it take and how does payment work?
After you confirm the drawings, production takes about 20–40 days and shipping about 28–40 days, followed by Uganda clearance and fitting on site. Payment is 10% before the 2D and 3D drawings, 40% before production, 40% before Uganda clearance and 10% after fitting.
Can I see samples before I decide?
Yes. Browse finishes and 360° room views in our Design Gallery, then compare the physical samples at our Kampala showroom, Monday to Saturday 08:30–18:00 (National Cleaning Day, the last Saturday of the month: 11:00–19:00; Sunday: VIP by appointment).
Start your project
Plan your wood-grain kitchen
Send your floor plan or photos and we will propose wood tones, layout and core mix for your room and budget.
Showroom
Visit our Kampala showroom
See cores, finishes and tall samples in person.
- Mon–Sat
- 08:30–18:00
- National Cleaning Day
- Last Saturday of the month, 11:00–19:00
- Sunday
- VIP by appointment
- Phone
- +256 393 102 850
+256 793 179 034
Wood-grain cabinets · Codes Y · YU
Wood-grain Cabinets Kampala — Warm Wood Finishes
Luxfit offers warm wood-grain finishes for Kampala kitchens and wardrobes, from pale oak and ash tones to deep walnut and espresso, carefully matched when a wood look is the brief. Structural cores follow the published mix: E1 11-layer plywood for wet zones and stone loads, particle board for tall wardrobe doors and MDF for painted or carved faces. Designed by Ugandans for Ugandans. Visit our Kampala showroom to compare real samples before you lock the quotation.
Why wood-grain
Why choose wood-grain cabinets?
Warm, natural look
Wood-grain finishes bring the warmth of timber to modern kitchens and bedrooms.
Stable cores
Engineered cores are specified by use, so doors and carcases stay flat and true.
Easy care
The fused surface resists scratches and moisture and wipes clean with a damp cloth.
Matched across rooms
Use the same wood-grain code on kitchen units, wardrobes and wall panels for a whole-home look.
Healthier boards
E0 particle board and E1 11-layer plywood; flagship builds use ENF-grade boards with MDI adhesive.
Compare real samples
Wood tones read differently in daylight. See the physical samples at our showroom before you decide.
Wood tones
Wood-grain tones: pale oak to deep walnut
Each wood-grain finish has a Y or YU code. Open a tone below to see it in a 3D room, or browse them all in Finishes & 3D Rooms.
Design Gallery
Wood-grain kitchens & wardrobes
Each design visual opens in our Design Gallery with its layout, finishes and key features.
Specification
Wood-grain cabinet specification
Typical specification
- Finish
- Wood-grain melamine (Y and YU codes)
- Carcase
- E0 particle board; E1 11-layer plywood for wet zones and stone loads
- Tall doors
- High-density particle board up to 2.7 m
- Edges
- Matching edge banding
- Hardware
- Soft-close hinges and runners
Compare
- vs wood veneer
- Veneer is a thin slice of real timber with natural grain; wood-grain melamine is harder and easier to maintain
- vs lacquer
- Lacquer gives a smooth, deep painted colour
- Real timber faces
- See wood veneer cabinets
Indicative budgets
- Indicative kitchen budgets: about UGX 5–12 million (small), 12–25 million (medium) and 25–50 million (large), including cabinetry materials and countertops; appliances are not included. Final quotes depend on layout, finishes and site conditions after measurement.
Cabinet quality control system
Quality control, checked at every stage
Every Luxfit order goes through one quality system, run by Luxfit and our manufacturing partners. Your confirmed drawings feed the production system directly, every panel is labelled and tracked from cutting to packing, and checks are built into each stage rather than left to the end.
- 01
Site measure & confirmed drawings
Our technical team measures on site. Production only starts after you approve the 2D drawings and 3D mock-ups.
- 02
Incoming material inspection
Boards, edge banding and finishes are checked against your specification (board grade, E0 or E1, and finish code) before cutting.
- 03
Smart cutting & edge banding
Production data goes straight from your drawings to the CNC line. Panels are cut to 0.1 mm tolerance and each one gets a QR-coded label.
- 04
Drilling & sorting checks
Each panel is scanned before drilling, so holes follow the drawing and a wrong size or position is flagged. Sorting confirms no part is missing.
- 05
Finished-panel inspection
Inspectors check panel sizes, edge banding, colour and drill positions, then clean every panel so no dust remains before packing.
- 06
Hardware checks
Hinges, runners and fittings are picked by type and quantity for your order, then scanned and photo-checked.
- 07
Packing & dispatch
Packages are scanned to confirm quantities, clearly labelled and tracked in the warehouse until loading.
- 08
Fitting to your drawings
After shipping and Uganda clearance, our team fits your cabinets on site to your confirmed drawings.
Testing standards
Standards we build to
- Formaldehyde
- E0 particle board · E1 11-layer plywood · ENF-grade (≤0.025 mg/m³) on flagship builds
- Adhesive
- MDI medical-grade adhesive: waterproof, no toxic glues
- Machining
- CNC to 0.1 mm tolerance
- Lacquer
- Sprayed in layers and baked (oven-cured)
- Coatings
- Anti-fingerprint, scratch-resistant, UV-yellowing resistant (where specified)
- Hardware
- Soft-close hinges and runners; SUS304 stainless steel fittings; runners and lift mechanisms cycle-tested
- Order accuracy
- QR-coded panels scanned at cutting, drilling, sorting and packing
Board grades, finish codes and hardware are confirmed on your quotation.
Premium cabinets quality assurance
Quality partners behind every Luxfit cabinet
We work with established manufacturing and hardware partners and specify each component by use. The options below are confirmed on your quotation.
Partner factory
Automated production line
CNC cutting, edge banding and drilling on an automated line, for consistent quality and efficient production.
Hardware partner
Blum hinges & runners
Our premium hardware option: smooth, quiet soft-close movement for doors and drawers.
Hardware partner
DTC soft-close hinges
Our standard soft-closing hinges for base units, wall units and tall doors.
Storage fittings
Pull-outs & organisers
Pull-out baskets, organiser drawers and soft-close waste sorters (including HIGOLD) in SUS304 stainless steel and nano-coated aluminium.
Finish
Baked lacquer
L-code lacquer is sprayed in layers and oven-baked, like the paint on premium cars, for a smooth, deep, durable colour.
Boards
Healthier board system
E0 particle board, E1 11-layer plywood and ENF-grade flagship boards, bonded with MDI adhesive.
How it works
How it works: from floor plan to fitting
Payment follows 10% before 2D/3D → 40% before production → 40% before Uganda clearance → 10% after fitting. Full stages are in our guide to lead time for Kampala kitchens and wardrobes.
- 01
Share your plan
Send your inquiry with a floor plan or photos to our sales team.
- 02
Site measure
Our technical team measures on site so the drawings match the real space.
- 03
2D & 3D design
After the 10% design deposit you receive 2D drawings and 3D mock-ups, with three revisions included.
- 04
Production
You confirm the design and pay 40% before production. Production takes about 20–40 days.
- 05
Shipping & clearance
Shipping takes about 28–40 days. 40% is due before Uganda clearance.
- 06
Fitting
Our team fits your cabinets on site. The final 10% is paid after fitting.
Explore
More cabinet materials & finishes
FAQ
Wood-grain cabinets: frequently asked questions
Are wood-grain cabinets made of solid timber?
No. Our wood-grain cabinets use wood-grain melamine finishes (Y and YU codes) on stable engineered cores: E0 particle board, E1 11-layer plywood or particle board, specified by use. For real timber faces, see our wood veneer cabinets.
Which wood tones are available?
From pale oak and ash to warm walnut, smoked walnut and espresso. Browse the codes in Finishes & 3D Rooms and compare the physical samples at our showroom.
Can my kitchen and wardrobes match?
Yes. The same wood-grain code can be used on kitchen units, wardrobes and wall panels for a coordinated, whole-home look.
How do I clean wood-grain cabinets?
Wipe with a damp cloth and mild soap. Avoid abrasive scrubbers. No oiling or waxing is needed.
How long does it take and how does payment work?
After you confirm the drawings, production takes about 20–40 days and shipping about 28–40 days, followed by Uganda clearance and fitting on site. Payment is 10% before the 2D and 3D drawings, 40% before production, 40% before Uganda clearance and 10% after fitting.
Can I see samples before I decide?
Yes. Browse finishes and 360° room views in our Design Gallery, then compare the physical samples at our Kampala showroom, Monday to Saturday 08:30–18:00 (National Cleaning Day, the last Saturday of the month: 11:00–19:00; Sunday: VIP by appointment).
Start your project
Plan your wood-grain kitchen
Send your floor plan or photos and we will propose wood tones, layout and core mix for your room and budget.
Showroom
Visit our Kampala showroom
See cores, finishes and tall samples in person.
- Mon–Sat
- 08:30–18:00
- National Cleaning Day
- Last Saturday of the month, 11:00–19:00
- Sunday
- VIP by appointment
- Phone
- +256 393 102 850
+256 793 179 034