PVC cabinetry · Vacuum-formed film
PVC Kitchen Cabinets
Moisture-resistant and low-maintenance, Luxfit PVC cabinetry suits humid climates and busy kitchens that demand long-term performance. PVC film is vacuum-formed over MDF door panels, sealing the face and edges in one smooth, wipe-clean surface, and it can wrap shaker and routed door profiles that flat laminates cannot.
Why PVC
Why choose PVC kitchen cabinets?
PVC wrapping applies a flexible film over MDF panels using vacuum-forming technology. The result is a sealed, moisture-resistant cabinet surface without the premium price of lacquer.
Superior moisture resistance
The PVC film seals the substrate against spills, splashes, steam and humidity, so doors keep their form in busy kitchens.
Low maintenance
The smooth, non-porous surface cleans with soap and water: no oiling, painting or sealing.
Colour & finish options
Solid colours, high-gloss, matte and realistic wood-grain films.
Handles kitchen heat
Withstands normal kitchen heat from ovens and dishwashers and resists common kitchen oils and cleaning products.
Edge-sealed construction
Every cabinet face is sealed, including the edges, so no board is exposed.
Cost-effective premium look
A modern, seamless finish comparable to lacquer at a lower price point, with shaker and routed profiles.
Design styles
PVC kitchen design styles
Popular looks for PVC doors, from white shaker to wood-grain and two-tone. Each design visual opens in our Design Gallery; your finish is confirmed on your quotation.
Specification
PVC cabinet specification
Typical specification
- Door finish
- PVC film, vacuum-formed over the door
- Substrate
- E1 MDF for stability
- Edges
- All-edge PVC sealing, no exposed board
- Profiles
- Flat, shaker and routed
- Carcase
- E0 particle board; E1 11-layer plywood for wet zones
- Hardware
- Soft-close hardware as standard
Compare
- vs lacquer (L)
- Lacquer is sprayed and baked for a deep painted colour; PVC gives a similar seamless look at a lower price point
- vs PET (K)
- PET is a tough polyester film for flat doors in an even colour
- vs melamine
- Melamine is a fused paper finish on flat panels; PVC can wrap profiled doors
Indicative budgets
- Indicative kitchen budgets: about UGX 5–12 million (small), 12–25 million (medium) and 25–50 million (large), including cabinetry materials and countertops; appliances are not included. Final quotes depend on layout, finishes and site conditions after measurement.
Cabinet quality control system
Quality control, checked at every stage
Every Luxfit order goes through one quality system, run by Luxfit and our manufacturing partners. Your confirmed drawings feed the production system directly, every panel is labelled and tracked from cutting to packing, and checks are built into each stage rather than left to the end.
- 01
Site measure & confirmed drawings
Our technical team measures on site. Production only starts after you approve the 2D drawings and 3D mock-ups.
- 02
Incoming material inspection
Boards, edge banding and finishes are checked against your specification (board grade, E0 or E1, and finish code) before cutting.
- 03
Smart cutting & edge banding
Production data goes straight from your drawings to the CNC line. Panels are cut to 0.1 mm tolerance and each one gets a QR-coded label.
- 04
Drilling & sorting checks
Each panel is scanned before drilling, so holes follow the drawing and a wrong size or position is flagged. Sorting confirms no part is missing.
- 05
Finished-panel inspection
Inspectors check panel sizes, edge banding, colour and drill positions, then clean every panel so no dust remains before packing.
- 06
Hardware checks
Hinges, runners and fittings are picked by type and quantity for your order, then scanned and photo-checked.
- 07
Packing & dispatch
Packages are scanned to confirm quantities, clearly labelled and tracked in the warehouse until loading.
- 08
Fitting to your drawings
After shipping and Uganda clearance, our team fits your cabinets on site to your confirmed drawings.
Testing standards
Standards we build to
- Formaldehyde
- E0 particle board · E1 11-layer plywood · ENF-grade (≤0.025 mg/m³) on flagship builds
- Adhesive
- MDI medical-grade adhesive: waterproof, no toxic glues
- Machining
- CNC to 0.1 mm tolerance
- Lacquer
- Sprayed in layers and baked (oven-cured)
- Coatings
- Anti-fingerprint, scratch-resistant, UV-yellowing resistant (where specified)
- Hardware
- Soft-close hinges and runners; SUS304 stainless steel fittings; runners and lift mechanisms cycle-tested
- Order accuracy
- QR-coded panels scanned at cutting, drilling, sorting and packing
Board grades, finish codes and hardware are confirmed on your quotation.
Premium cabinets quality assurance
Quality partners behind every Luxfit cabinet
We work with established manufacturing and hardware partners and specify each component by use. The options below are confirmed on your quotation.
Partner factory
Automated production line
CNC cutting, edge banding and drilling on an automated line, for consistent quality and efficient production.
Hardware partner
Blum hinges & runners
Our premium hardware option: smooth, quiet soft-close movement for doors and drawers.
Hardware partner
DTC soft-close hinges
Our standard soft-closing hinges for base units, wall units and tall doors.
Storage fittings
Pull-outs & organisers
Pull-out baskets, organiser drawers and soft-close waste sorters (including HIGOLD) in SUS304 stainless steel and nano-coated aluminium.
Finish
Baked lacquer
L-code lacquer is sprayed in layers and oven-baked, like the paint on premium cars, for a smooth, deep, durable colour.
Boards
Healthier board system
E0 particle board, E1 11-layer plywood and ENF-grade flagship boards, bonded with MDI adhesive.
How it works
How it works: from floor plan to fitting
Payment follows 10% before 2D/3D → 40% before production → 40% before Uganda clearance → 10% after fitting. Full stages are in our guide to lead time for Kampala kitchens and wardrobes.
- 01
Share your plan
Send your inquiry with a floor plan or photos to our sales team.
- 02
Site measure
Our technical team measures on site so the drawings match the real space.
- 03
2D & 3D design
After the 10% design deposit you receive 2D drawings and 3D mock-ups, with three revisions included.
- 04
Production
You confirm the design and pay 40% before production. Production takes about 20–40 days.
- 05
Shipping & clearance
Shipping takes about 28–40 days. 40% is due before Uganda clearance.
- 06
Fitting
Our team fits your cabinets on site. The final 10% is paid after fitting.
Explore
More cabinet materials & finishes
FAQ
PVC cabinets: frequently asked questions
Are PVC cabinets suitable for food preparation areas?
Yes. The smooth, non-porous PVC surface does not absorb odours or stains and wipes clean easily. Cores follow our healthier board system, with E1 MDF doors.
How long do PVC kitchen cabinets last?
With normal care, PVC doors keep their look for many years. The sealed face and edges protect the MDF core from splashes and steam, and the surface does not need refinishing.
Can PVC cabinets handle kitchen heat?
PVC cabinets are designed for normal kitchen heat from ovens, dishwashers and cooking appliances. We recommend heat shields next to high-temperature appliances as a best practice.
How do I clean PVC cabinets?
Wipe with a damp cloth and mild soap. The non-porous surface repels grease and stains. Avoid abrasive scrubbers, which can dull the finish.
What design options are available for PVC cabinets?
PVC film comes in solid colours, high-gloss, matte and wood-grain. It can wrap routed profiles for shaker and raised-panel door styles. Ask to see colour and profile samples at our showroom.
How long does it take and how does payment work?
After you confirm the drawings, production takes about 20–40 days and shipping about 28–40 days, followed by Uganda clearance and fitting on site. Payment is 10% before the 2D and 3D drawings, 40% before production, 40% before Uganda clearance and 10% after fitting.
Start your project
Ready for a moisture-resistant, low-maintenance kitchen?
Get a design consultation and quote from Luxfit. We measure on site, design in 2D and 3D, then manufacture and fit your PVC kitchen.
Showroom
Visit our Kampala showroom
See cores, finishes and tall samples in person.
- Mon–Sat
- 08:30–18:00
- National Cleaning Day
- Last Saturday of the month, 11:00–19:00
- Sunday
- VIP by appointment
- Phone
- +256 393 102 850
+256 793 179 034
PVC cabinetry · Vacuum-formed film
PVC Kitchen Cabinets
Moisture-resistant and low-maintenance, Luxfit PVC cabinetry suits humid climates and busy kitchens that demand long-term performance. PVC film is vacuum-formed over MDF door panels, sealing the face and edges in one smooth, wipe-clean surface, and it can wrap shaker and routed door profiles that flat laminates cannot.
Why PVC
Why choose PVC kitchen cabinets?
PVC wrapping applies a flexible film over MDF panels using vacuum-forming technology. The result is a sealed, moisture-resistant cabinet surface without the premium price of lacquer.
Superior moisture resistance
The PVC film seals the substrate against spills, splashes, steam and humidity, so doors keep their form in busy kitchens.
Low maintenance
The smooth, non-porous surface cleans with soap and water: no oiling, painting or sealing.
Colour & finish options
Solid colours, high-gloss, matte and realistic wood-grain films.
Handles kitchen heat
Withstands normal kitchen heat from ovens and dishwashers and resists common kitchen oils and cleaning products.
Edge-sealed construction
Every cabinet face is sealed, including the edges, so no board is exposed.
Cost-effective premium look
A modern, seamless finish comparable to lacquer at a lower price point, with shaker and routed profiles.
Design styles
PVC kitchen design styles
Popular looks for PVC doors, from white shaker to wood-grain and two-tone. Each design visual opens in our Design Gallery; your finish is confirmed on your quotation.
Specification
PVC cabinet specification
Typical specification
- Door finish
- PVC film, vacuum-formed over the door
- Substrate
- E1 MDF for stability
- Edges
- All-edge PVC sealing, no exposed board
- Profiles
- Flat, shaker and routed
- Carcase
- E0 particle board; E1 11-layer plywood for wet zones
- Hardware
- Soft-close hardware as standard
Compare
- vs lacquer (L)
- Lacquer is sprayed and baked for a deep painted colour; PVC gives a similar seamless look at a lower price point
- vs PET (K)
- PET is a tough polyester film for flat doors in an even colour
- vs melamine
- Melamine is a fused paper finish on flat panels; PVC can wrap profiled doors
Indicative budgets
- Indicative kitchen budgets: about UGX 5–12 million (small), 12–25 million (medium) and 25–50 million (large), including cabinetry materials and countertops; appliances are not included. Final quotes depend on layout, finishes and site conditions after measurement.
Cabinet quality control system
Quality control, checked at every stage
Every Luxfit order goes through one quality system, run by Luxfit and our manufacturing partners. Your confirmed drawings feed the production system directly, every panel is labelled and tracked from cutting to packing, and checks are built into each stage rather than left to the end.
- 01
Site measure & confirmed drawings
Our technical team measures on site. Production only starts after you approve the 2D drawings and 3D mock-ups.
- 02
Incoming material inspection
Boards, edge banding and finishes are checked against your specification (board grade, E0 or E1, and finish code) before cutting.
- 03
Smart cutting & edge banding
Production data goes straight from your drawings to the CNC line. Panels are cut to 0.1 mm tolerance and each one gets a QR-coded label.
- 04
Drilling & sorting checks
Each panel is scanned before drilling, so holes follow the drawing and a wrong size or position is flagged. Sorting confirms no part is missing.
- 05
Finished-panel inspection
Inspectors check panel sizes, edge banding, colour and drill positions, then clean every panel so no dust remains before packing.
- 06
Hardware checks
Hinges, runners and fittings are picked by type and quantity for your order, then scanned and photo-checked.
- 07
Packing & dispatch
Packages are scanned to confirm quantities, clearly labelled and tracked in the warehouse until loading.
- 08
Fitting to your drawings
After shipping and Uganda clearance, our team fits your cabinets on site to your confirmed drawings.
Testing standards
Standards we build to
- Formaldehyde
- E0 particle board · E1 11-layer plywood · ENF-grade (≤0.025 mg/m³) on flagship builds
- Adhesive
- MDI medical-grade adhesive: waterproof, no toxic glues
- Machining
- CNC to 0.1 mm tolerance
- Lacquer
- Sprayed in layers and baked (oven-cured)
- Coatings
- Anti-fingerprint, scratch-resistant, UV-yellowing resistant (where specified)
- Hardware
- Soft-close hinges and runners; SUS304 stainless steel fittings; runners and lift mechanisms cycle-tested
- Order accuracy
- QR-coded panels scanned at cutting, drilling, sorting and packing
Board grades, finish codes and hardware are confirmed on your quotation.
Premium cabinets quality assurance
Quality partners behind every Luxfit cabinet
We work with established manufacturing and hardware partners and specify each component by use. The options below are confirmed on your quotation.
Partner factory
Automated production line
CNC cutting, edge banding and drilling on an automated line, for consistent quality and efficient production.
Hardware partner
Blum hinges & runners
Our premium hardware option: smooth, quiet soft-close movement for doors and drawers.
Hardware partner
DTC soft-close hinges
Our standard soft-closing hinges for base units, wall units and tall doors.
Storage fittings
Pull-outs & organisers
Pull-out baskets, organiser drawers and soft-close waste sorters (including HIGOLD) in SUS304 stainless steel and nano-coated aluminium.
Finish
Baked lacquer
L-code lacquer is sprayed in layers and oven-baked, like the paint on premium cars, for a smooth, deep, durable colour.
Boards
Healthier board system
E0 particle board, E1 11-layer plywood and ENF-grade flagship boards, bonded with MDI adhesive.
How it works
How it works: from floor plan to fitting
Payment follows 10% before 2D/3D → 40% before production → 40% before Uganda clearance → 10% after fitting. Full stages are in our guide to lead time for Kampala kitchens and wardrobes.
- 01
Share your plan
Send your inquiry with a floor plan or photos to our sales team.
- 02
Site measure
Our technical team measures on site so the drawings match the real space.
- 03
2D & 3D design
After the 10% design deposit you receive 2D drawings and 3D mock-ups, with three revisions included.
- 04
Production
You confirm the design and pay 40% before production. Production takes about 20–40 days.
- 05
Shipping & clearance
Shipping takes about 28–40 days. 40% is due before Uganda clearance.
- 06
Fitting
Our team fits your cabinets on site. The final 10% is paid after fitting.
Explore
More cabinet materials & finishes
FAQ
PVC cabinets: frequently asked questions
Are PVC cabinets suitable for food preparation areas?
Yes. The smooth, non-porous PVC surface does not absorb odours or stains and wipes clean easily. Cores follow our healthier board system, with E1 MDF doors.
How long do PVC kitchen cabinets last?
With normal care, PVC doors keep their look for many years. The sealed face and edges protect the MDF core from splashes and steam, and the surface does not need refinishing.
Can PVC cabinets handle kitchen heat?
PVC cabinets are designed for normal kitchen heat from ovens, dishwashers and cooking appliances. We recommend heat shields next to high-temperature appliances as a best practice.
How do I clean PVC cabinets?
Wipe with a damp cloth and mild soap. The non-porous surface repels grease and stains. Avoid abrasive scrubbers, which can dull the finish.
What design options are available for PVC cabinets?
PVC film comes in solid colours, high-gloss, matte and wood-grain. It can wrap routed profiles for shaker and raised-panel door styles. Ask to see colour and profile samples at our showroom.
How long does it take and how does payment work?
After you confirm the drawings, production takes about 20–40 days and shipping about 28–40 days, followed by Uganda clearance and fitting on site. Payment is 10% before the 2D and 3D drawings, 40% before production, 40% before Uganda clearance and 10% after fitting.
Start your project
Ready for a moisture-resistant, low-maintenance kitchen?
Get a design consultation and quote from Luxfit. We measure on site, design in 2D and 3D, then manufacture and fit your PVC kitchen.
Showroom
Visit our Kampala showroom
See cores, finishes and tall samples in person.
- Mon–Sat
- 08:30–18:00
- National Cleaning Day
- Last Saturday of the month, 11:00–19:00
- Sunday
- VIP by appointment
- Phone
- +256 393 102 850
+256 793 179 034