Plywood cabinets · E1 11-layer core
Plywood Cabinets Kampala — 11-Layer Core
Luxfit specifies E1 11-layer cross-bonded plywood for kitchen and bathroom carcases that face moisture and heavy stone countertops. Eleven veneer layers, more than typical five-to-seven-layer board, add about 40% more structural stability and help resist sagging under stone loads. Measured on site and CNC-cut at 0.1 mm for a clean fit. Designed by Ugandans for Ugandans.
Best for
Where we specify 11-layer plywood
Carcases are specified by use, not one board for every room. The site measure confirms plumbing, splash risk and stone loads before we lock the core mix.
Kitchens with stone tops
When granite or stone counters are confirmed, 11-layer plywood is our load-and-span flagship for base cabinets and wet-zone runs.
Bathrooms & splash-prone zones
Moisture and humidity stress ordinary cores. Cross-bonded 11-layer plywood is the preferred carcase for vanities and wet-zone storage.
Structural spans & heavy shelves
Long spans and loaded shelves stay straight on the cross-bonded core.
Strength under stone
Eleven cross-bonded layers improve dimensional stability and screw holding versus thinner boards.
Precision fit
CNC at 0.1 mm supports seamless joins and a zero-gap fit once drawings are approved.
Healthier core
E1 plywood with MDI medical-grade adhesive where specified; flagship builds use ENF-grade boards (≤0.025 mg/m³).
Design Gallery
Kitchens with stone-look tops
Heavy tops are where the 11-layer core earns its place. Each design visual opens in our Design Gallery with its layout, finishes and key features.
Specification
Plywood cabinet specification
Typical specification
- Core
- 11-layer cross-bonded plywood
- Grade
- E1 (ENF-grade on flagship builds)
- Adhesive
- MDI medical-grade (where specified)
- Machining
- CNC to 0.1 mm tolerance
- Doors
- Melamine (Y, YU, BK), lacquer (L) or PET (K)
- Hardware
- Soft-close hinges and runners
Compare
- vs typical 5–7 layer
- About 40% more structural stability
- vs particle board
- High-density particle board stays flatter on tall doors; 11-layer plywood wins on load (stone counters, heavy shelves)
- vs MDF
- MDF is the smooth board for painted and lacquer doors; plywood is the structural core
Indicative budgets
- Indicative kitchen budgets: about UGX 5–12 million (small), 12–25 million (medium) and 25–50 million (large), including cabinetry materials and countertops; appliances are not included. Final quotes depend on layout, finishes and site conditions after measurement.
Cabinet quality control system
Quality control, checked at every stage
Every Luxfit order goes through one quality system, run by Luxfit and our manufacturing partners. Your confirmed drawings feed the production system directly, every panel is labelled and tracked from cutting to packing, and checks are built into each stage rather than left to the end.
- 01
Site measure & confirmed drawings
Our technical team measures on site. Production only starts after you approve the 2D drawings and 3D mock-ups.
- 02
Incoming material inspection
Boards, edge banding and finishes are checked against your specification (board grade, E0 or E1, and finish code) before cutting.
- 03
Smart cutting & edge banding
Production data goes straight from your drawings to the CNC line. Panels are cut to 0.1 mm tolerance and each one gets a QR-coded label.
- 04
Drilling & sorting checks
Each panel is scanned before drilling, so holes follow the drawing and a wrong size or position is flagged. Sorting confirms no part is missing.
- 05
Finished-panel inspection
Inspectors check panel sizes, edge banding, colour and drill positions, then clean every panel so no dust remains before packing.
- 06
Hardware checks
Hinges, runners and fittings are picked by type and quantity for your order, then scanned and photo-checked.
- 07
Packing & dispatch
Packages are scanned to confirm quantities, clearly labelled and tracked in the warehouse until loading.
- 08
Fitting to your drawings
After shipping and Uganda clearance, our team fits your cabinets on site to your confirmed drawings.
Testing standards
Standards we build to
- Formaldehyde
- E0 particle board · E1 11-layer plywood · ENF-grade (≤0.025 mg/m³) on flagship builds
- Adhesive
- MDI medical-grade adhesive: waterproof, no toxic glues
- Machining
- CNC to 0.1 mm tolerance
- Lacquer
- Sprayed in layers and baked (oven-cured)
- Coatings
- Anti-fingerprint, scratch-resistant, UV-yellowing resistant (where specified)
- Hardware
- Soft-close hinges and runners; SUS304 stainless steel fittings; runners and lift mechanisms cycle-tested
- Order accuracy
- QR-coded panels scanned at cutting, drilling, sorting and packing
Board grades, finish codes and hardware are confirmed on your quotation.
Premium cabinets quality assurance
Quality partners behind every Luxfit cabinet
We work with established manufacturing and hardware partners and specify each component by use. The options below are confirmed on your quotation.
Partner factory
Automated production line
CNC cutting, edge banding and drilling on an automated line, for consistent quality and efficient production.
Hardware partner
Blum hinges & runners
Our premium hardware option: smooth, quiet soft-close movement for doors and drawers.
Hardware partner
DTC soft-close hinges
Our standard soft-closing hinges for base units, wall units and tall doors.
Storage fittings
Pull-outs & organisers
Pull-out baskets, organiser drawers and soft-close waste sorters (including HIGOLD) in SUS304 stainless steel and nano-coated aluminium.
Finish
Baked lacquer
L-code lacquer is sprayed in layers and oven-baked, like the paint on premium cars, for a smooth, deep, durable colour.
Boards
Healthier board system
E0 particle board, E1 11-layer plywood and ENF-grade flagship boards, bonded with MDI adhesive.
How it works
How it works: from floor plan to fitting
Payment follows 10% before 2D/3D → 40% before production → 40% before Uganda clearance → 10% after fitting. Full stages are in our guide to lead time for Kampala kitchens and wardrobes.
- 01
Share your plan
Send your inquiry with a floor plan or photos to our sales team.
- 02
Site measure
Our technical team measures on site so the drawings match the real space.
- 03
2D & 3D design
After the 10% design deposit you receive 2D drawings and 3D mock-ups, with three revisions included.
- 04
Production
You confirm the design and pay 40% before production. Production takes about 20–40 days.
- 05
Shipping & clearance
Shipping takes about 28–40 days. 40% is due before Uganda clearance.
- 06
Fitting
Our team fits your cabinets on site. The final 10% is paid after fitting.
Explore
More cabinet materials & finishes
FAQ
Plywood cabinets: frequently asked questions
Why 11 layers?
Eleven cross-bonded veneer layers, instead of the typical five to seven, give about 40% more structural stability, so base cabinets resist sagging under heavy stone countertops.
Where do you use plywood instead of particle board?
We specify 11-layer plywood for sink runs, wet zones, stone-top base cabinets and heavy shelves. E0 particle board is used where appropriate, and high-density particle board for tall wardrobe doors.
Is plywood good for bathrooms?
Yes. Cross-bonded 11-layer plywood is our preferred carcase for vanities and splash-prone storage. Pair it with the finish series you choose for the doors.
Which grade is your plywood?
Our 11-layer plywood is E1, bonded with MDI medical-grade adhesive where specified. Flagship builds use ENF-grade boards (≤0.025 mg/m³). See E1 & ENF plywood and ENF vs E1.
How long does it take and how does payment work?
After you confirm the drawings, production takes about 20–40 days and shipping about 28–40 days, followed by Uganda clearance and fitting on site. Payment is 10% before the 2D and 3D drawings, 40% before production, 40% before Uganda clearance and 10% after fitting.
Can I see samples before I decide?
Yes. Browse finishes and 360° room views in our Design Gallery, then compare the physical samples at our Kampala showroom, Monday to Saturday 08:30–18:00 (National Cleaning Day, the last Saturday of the month: 11:00–19:00; Sunday: VIP by appointment).
Start your project
Plan your plywood kitchen
Send your floor plan or photos and we will confirm where the 11-layer core is needed for your sinks, wet zones and stone tops.
Showroom
Visit our Kampala showroom
See cores, finishes and tall samples in person.
- Mon–Sat
- 08:30–18:00
- National Cleaning Day
- Last Saturday of the month, 11:00–19:00
- Sunday
- VIP by appointment
- Phone
- +256 393 102 850
+256 793 179 034
Plywood cabinets · E1 11-layer core
Plywood Cabinets Kampala — 11-Layer Core
Luxfit specifies E1 11-layer cross-bonded plywood for kitchen and bathroom carcases that face moisture and heavy stone countertops. Eleven veneer layers, more than typical five-to-seven-layer board, add about 40% more structural stability and help resist sagging under stone loads. Measured on site and CNC-cut at 0.1 mm for a clean fit. Designed by Ugandans for Ugandans.
Best for
Where we specify 11-layer plywood
Carcases are specified by use, not one board for every room. The site measure confirms plumbing, splash risk and stone loads before we lock the core mix.
Kitchens with stone tops
When granite or stone counters are confirmed, 11-layer plywood is our load-and-span flagship for base cabinets and wet-zone runs.
Bathrooms & splash-prone zones
Moisture and humidity stress ordinary cores. Cross-bonded 11-layer plywood is the preferred carcase for vanities and wet-zone storage.
Structural spans & heavy shelves
Long spans and loaded shelves stay straight on the cross-bonded core.
Strength under stone
Eleven cross-bonded layers improve dimensional stability and screw holding versus thinner boards.
Precision fit
CNC at 0.1 mm supports seamless joins and a zero-gap fit once drawings are approved.
Healthier core
E1 plywood with MDI medical-grade adhesive where specified; flagship builds use ENF-grade boards (≤0.025 mg/m³).
Design Gallery
Kitchens with stone-look tops
Heavy tops are where the 11-layer core earns its place. Each design visual opens in our Design Gallery with its layout, finishes and key features.
Specification
Plywood cabinet specification
Typical specification
- Core
- 11-layer cross-bonded plywood
- Grade
- E1 (ENF-grade on flagship builds)
- Adhesive
- MDI medical-grade (where specified)
- Machining
- CNC to 0.1 mm tolerance
- Doors
- Melamine (Y, YU, BK), lacquer (L) or PET (K)
- Hardware
- Soft-close hinges and runners
Compare
- vs typical 5–7 layer
- About 40% more structural stability
- vs particle board
- High-density particle board stays flatter on tall doors; 11-layer plywood wins on load (stone counters, heavy shelves)
- vs MDF
- MDF is the smooth board for painted and lacquer doors; plywood is the structural core
Indicative budgets
- Indicative kitchen budgets: about UGX 5–12 million (small), 12–25 million (medium) and 25–50 million (large), including cabinetry materials and countertops; appliances are not included. Final quotes depend on layout, finishes and site conditions after measurement.
Cabinet quality control system
Quality control, checked at every stage
Every Luxfit order goes through one quality system, run by Luxfit and our manufacturing partners. Your confirmed drawings feed the production system directly, every panel is labelled and tracked from cutting to packing, and checks are built into each stage rather than left to the end.
- 01
Site measure & confirmed drawings
Our technical team measures on site. Production only starts after you approve the 2D drawings and 3D mock-ups.
- 02
Incoming material inspection
Boards, edge banding and finishes are checked against your specification (board grade, E0 or E1, and finish code) before cutting.
- 03
Smart cutting & edge banding
Production data goes straight from your drawings to the CNC line. Panels are cut to 0.1 mm tolerance and each one gets a QR-coded label.
- 04
Drilling & sorting checks
Each panel is scanned before drilling, so holes follow the drawing and a wrong size or position is flagged. Sorting confirms no part is missing.
- 05
Finished-panel inspection
Inspectors check panel sizes, edge banding, colour and drill positions, then clean every panel so no dust remains before packing.
- 06
Hardware checks
Hinges, runners and fittings are picked by type and quantity for your order, then scanned and photo-checked.
- 07
Packing & dispatch
Packages are scanned to confirm quantities, clearly labelled and tracked in the warehouse until loading.
- 08
Fitting to your drawings
After shipping and Uganda clearance, our team fits your cabinets on site to your confirmed drawings.
Testing standards
Standards we build to
- Formaldehyde
- E0 particle board · E1 11-layer plywood · ENF-grade (≤0.025 mg/m³) on flagship builds
- Adhesive
- MDI medical-grade adhesive: waterproof, no toxic glues
- Machining
- CNC to 0.1 mm tolerance
- Lacquer
- Sprayed in layers and baked (oven-cured)
- Coatings
- Anti-fingerprint, scratch-resistant, UV-yellowing resistant (where specified)
- Hardware
- Soft-close hinges and runners; SUS304 stainless steel fittings; runners and lift mechanisms cycle-tested
- Order accuracy
- QR-coded panels scanned at cutting, drilling, sorting and packing
Board grades, finish codes and hardware are confirmed on your quotation.
Premium cabinets quality assurance
Quality partners behind every Luxfit cabinet
We work with established manufacturing and hardware partners and specify each component by use. The options below are confirmed on your quotation.
Partner factory
Automated production line
CNC cutting, edge banding and drilling on an automated line, for consistent quality and efficient production.
Hardware partner
Blum hinges & runners
Our premium hardware option: smooth, quiet soft-close movement for doors and drawers.
Hardware partner
DTC soft-close hinges
Our standard soft-closing hinges for base units, wall units and tall doors.
Storage fittings
Pull-outs & organisers
Pull-out baskets, organiser drawers and soft-close waste sorters (including HIGOLD) in SUS304 stainless steel and nano-coated aluminium.
Finish
Baked lacquer
L-code lacquer is sprayed in layers and oven-baked, like the paint on premium cars, for a smooth, deep, durable colour.
Boards
Healthier board system
E0 particle board, E1 11-layer plywood and ENF-grade flagship boards, bonded with MDI adhesive.
How it works
How it works: from floor plan to fitting
Payment follows 10% before 2D/3D → 40% before production → 40% before Uganda clearance → 10% after fitting. Full stages are in our guide to lead time for Kampala kitchens and wardrobes.
- 01
Share your plan
Send your inquiry with a floor plan or photos to our sales team.
- 02
Site measure
Our technical team measures on site so the drawings match the real space.
- 03
2D & 3D design
After the 10% design deposit you receive 2D drawings and 3D mock-ups, with three revisions included.
- 04
Production
You confirm the design and pay 40% before production. Production takes about 20–40 days.
- 05
Shipping & clearance
Shipping takes about 28–40 days. 40% is due before Uganda clearance.
- 06
Fitting
Our team fits your cabinets on site. The final 10% is paid after fitting.
Explore
More cabinet materials & finishes
FAQ
Plywood cabinets: frequently asked questions
Why 11 layers?
Eleven cross-bonded veneer layers, instead of the typical five to seven, give about 40% more structural stability, so base cabinets resist sagging under heavy stone countertops.
Where do you use plywood instead of particle board?
We specify 11-layer plywood for sink runs, wet zones, stone-top base cabinets and heavy shelves. E0 particle board is used where appropriate, and high-density particle board for tall wardrobe doors.
Is plywood good for bathrooms?
Yes. Cross-bonded 11-layer plywood is our preferred carcase for vanities and splash-prone storage. Pair it with the finish series you choose for the doors.
Which grade is your plywood?
Our 11-layer plywood is E1, bonded with MDI medical-grade adhesive where specified. Flagship builds use ENF-grade boards (≤0.025 mg/m³). See E1 & ENF plywood and ENF vs E1.
How long does it take and how does payment work?
After you confirm the drawings, production takes about 20–40 days and shipping about 28–40 days, followed by Uganda clearance and fitting on site. Payment is 10% before the 2D and 3D drawings, 40% before production, 40% before Uganda clearance and 10% after fitting.
Can I see samples before I decide?
Yes. Browse finishes and 360° room views in our Design Gallery, then compare the physical samples at our Kampala showroom, Monday to Saturday 08:30–18:00 (National Cleaning Day, the last Saturday of the month: 11:00–19:00; Sunday: VIP by appointment).
Start your project
Plan your plywood kitchen
Send your floor plan or photos and we will confirm where the 11-layer core is needed for your sinks, wet zones and stone tops.
Showroom
Visit our Kampala showroom
See cores, finishes and tall samples in person.
- Mon–Sat
- 08:30–18:00
- National Cleaning Day
- Last Saturday of the month, 11:00–19:00
- Sunday
- VIP by appointment
- Phone
- +256 393 102 850
+256 793 179 034