Low density · ≤600 kg/m³
Back panels & screens
For back panels, decorative screens and weight-sensitive parts: the economy entry.
Particle board · E0
Particle Board Cabinets Kampala — Particle board for Tall Doors
Luxfit uses E0 particle board where the project calls for it, and specifies high-density particle board (700–800 kg/m³) for large wardrobe doors that must stay flat. Particle board is engineered with strong anti-warping behaviour and no “internal memory,” supporting floor-to-ceiling doors up to 2.7 metres. MDI bonding improves water resistance versus typical retail particle board. Designed by Ugandans for Ugandans.
Why particle board
Why choose particle board cabinets?
Tall doors that stay flat
High-density particle board supports floor-to-ceiling wardrobe doors up to 2.7 m.
Anti-warp, no memory
Engineered with strong anti-warping behaviour and no “internal memory”, so doors stay straight.
Water-resistant bond
MDI bonding is more water-resistant than typical retail particle board.
E0 health grade
Luxfit specifies E0 for particle boards; flagship builds use ENF-grade boards (≤0.025 mg/m³).
Smooth for melamine
A flat, even face for melamine finishes in solid colours, wood-grains and textures.
Right board for each part
Low-density board for back panels and screens, high density for doors, plywood where loads are heavy.
Density matters
Choose the right density
Not every part needs the same board. We match density to the job.
High density · 700–800 kg/m³
Tall wardrobe doors
For floor-to-ceiling wardrobe doors up to 2.7 m: stays straight, no “internal memory”, MDI bond.
For heavy loads
11-layer plywood
High-density particle board wins on staying straight; 11-layer plywood still wins on load (granite counters, heavy shelves).
Plywood cabinetsDesign Gallery
Kitchens & wardrobes on engineered cores
Each design visual opens in our Design Gallery with its layout, finishes and key features.
Specification
Particle board cabinet specification
Typical specification
- Carcase
- E0 particle board
- Tall doors
- High-density particle board, 700–800 kg/m³, up to 2.7 m
- Back panels
- Low-density board (≤600 kg/m³) where weight matters
- Bond
- MDI adhesive
- Finish
- Melamine (Y, YU, BK) and other finish series
- Machining
- CNC to 0.1 mm tolerance
Compare
- vs 11-layer plywood
- Plywood wins on load: sink runs, wet zones, stone tops, heavy shelves
- vs MDF
- MDF is the smooth board for lacquer and CNC-carved doors
- vs retail particle board
- MDI bond is more water-resistant
Indicative budgets
- Indicative kitchen budgets: about UGX 5–12 million (small), 12–25 million (medium) and 25–50 million (large), including cabinetry materials and countertops; appliances are not included. Final quotes depend on layout, finishes and site conditions after measurement.
Cabinet quality control system
Quality control, checked at every stage
Every Luxfit order goes through one quality system, run by Luxfit and our manufacturing partners. Your confirmed drawings feed the production system directly, every panel is labelled and tracked from cutting to packing, and checks are built into each stage rather than left to the end.
- 01
Site measure & confirmed drawings
Our technical team measures on site. Production only starts after you approve the 2D drawings and 3D mock-ups.
- 02
Incoming material inspection
Boards, edge banding and finishes are checked against your specification (board grade, E0 or E1, and finish code) before cutting.
- 03
Smart cutting & edge banding
Production data goes straight from your drawings to the CNC line. Panels are cut to 0.1 mm tolerance and each one gets a QR-coded label.
- 04
Drilling & sorting checks
Each panel is scanned before drilling, so holes follow the drawing and a wrong size or position is flagged. Sorting confirms no part is missing.
- 05
Finished-panel inspection
Inspectors check panel sizes, edge banding, colour and drill positions, then clean every panel so no dust remains before packing.
- 06
Hardware checks
Hinges, runners and fittings are picked by type and quantity for your order, then scanned and photo-checked.
- 07
Packing & dispatch
Packages are scanned to confirm quantities, clearly labelled and tracked in the warehouse until loading.
- 08
Fitting to your drawings
After shipping and Uganda clearance, our team fits your cabinets on site to your confirmed drawings.
Testing standards
Standards we build to
- Formaldehyde
- E0 particle board · E1 11-layer plywood · ENF-grade (≤0.025 mg/m³) on flagship builds
- Adhesive
- MDI medical-grade adhesive: waterproof, no toxic glues
- Machining
- CNC to 0.1 mm tolerance
- Lacquer
- Sprayed in layers and baked (oven-cured)
- Coatings
- Anti-fingerprint, scratch-resistant, UV-yellowing resistant (where specified)
- Hardware
- Soft-close hinges and runners; SUS304 stainless steel fittings; runners and lift mechanisms cycle-tested
- Order accuracy
- QR-coded panels scanned at cutting, drilling, sorting and packing
Board grades, finish codes and hardware are confirmed on your quotation.
Premium cabinets quality assurance
Quality partners behind every Luxfit cabinet
We work with established manufacturing and hardware partners and specify each component by use. The options below are confirmed on your quotation.
Partner factory
Automated production line
CNC cutting, edge banding and drilling on an automated line, for consistent quality and efficient production.
Hardware partner
Blum hinges & runners
Our premium hardware option: smooth, quiet soft-close movement for doors and drawers.
Hardware partner
DTC soft-close hinges
Our standard soft-closing hinges for base units, wall units and tall doors.
Storage fittings
Pull-outs & organisers
Pull-out baskets, organiser drawers and soft-close waste sorters (including HIGOLD) in SUS304 stainless steel and nano-coated aluminium.
Finish
Baked lacquer
L-code lacquer is sprayed in layers and oven-baked, like the paint on premium cars, for a smooth, deep, durable colour.
Boards
Healthier board system
E0 particle board, E1 11-layer plywood and ENF-grade flagship boards, bonded with MDI adhesive.
How it works
How it works: from floor plan to fitting
Payment follows 10% before 2D/3D → 40% before production → 40% before Uganda clearance → 10% after fitting. Full stages are in our guide to lead time for Kampala kitchens and wardrobes.
- 01
Share your plan
Send your inquiry with a floor plan or photos to our sales team.
- 02
Site measure
Our technical team measures on site so the drawings match the real space.
- 03
2D & 3D design
After the 10% design deposit you receive 2D drawings and 3D mock-ups, with three revisions included.
- 04
Production
You confirm the design and pay 40% before production. Production takes about 20–40 days.
- 05
Shipping & clearance
Shipping takes about 28–40 days. 40% is due before Uganda clearance.
- 06
Fitting
Our team fits your cabinets on site. The final 10% is paid after fitting.
Explore
More cabinet materials & finishes
FAQ
Particle board cabinets: frequently asked questions
What is particle board?
Particle board is Luxfit’s engineered particle board. The high-density grade (700–800 kg/m³) is made for large wardrobe doors: it stays flat, has no “internal memory” and supports floor-to-ceiling doors up to 2.7 m.
Is particle board strong enough for kitchens?
Yes, for carcases and wall units where it is specified. For sink runs, wet zones and stone countertop loads we specify E1 11-layer plywood, which wins on load.
Does particle board handle moisture?
Our boards are bonded with MDI adhesive, which is more water-resistant than typical retail particle board. Wet zones still get the 11-layer plywood core.
Which grade is your particle board?
Luxfit specifies E0 for particle boards. Flagship builds use ENF-grade boards (≤0.025 mg/m³). See ENF vs E1.
How long does it take and how does payment work?
After you confirm the drawings, production takes about 20–40 days and shipping about 28–40 days, followed by Uganda clearance and fitting on site. Payment is 10% before the 2D and 3D drawings, 40% before production, 40% before Uganda clearance and 10% after fitting.
Can I see samples before I decide?
Yes. Browse finishes and 360° room views in our Design Gallery, then compare the physical samples at our Kampala showroom, Monday to Saturday 08:30–18:00 (National Cleaning Day, the last Saturday of the month: 11:00–19:00; Sunday: VIP by appointment).
Start your project
Plan your cabinets with Luxfit
Send your floor plan or photos and we will propose the right board for each part of your kitchen or wardrobe.
Showroom
Visit our Kampala showroom
See cores, finishes and tall samples in person.
- Mon–Sat
- 08:30–18:00
- National Cleaning Day
- Last Saturday of the month, 11:00–19:00
- Sunday
- VIP by appointment
- Phone
- +256 393 102 850
+256 793 179 034
Particle board · E0
Particle Board Cabinets Kampala — Particle board for Tall Doors
Luxfit uses E0 particle board where the project calls for it, and specifies high-density particle board (700–800 kg/m³) for large wardrobe doors that must stay flat. Particle board is engineered with strong anti-warping behaviour and no “internal memory,” supporting floor-to-ceiling doors up to 2.7 metres. MDI bonding improves water resistance versus typical retail particle board. Designed by Ugandans for Ugandans.
Why particle board
Why choose particle board cabinets?
Tall doors that stay flat
High-density particle board supports floor-to-ceiling wardrobe doors up to 2.7 m.
Anti-warp, no memory
Engineered with strong anti-warping behaviour and no “internal memory”, so doors stay straight.
Water-resistant bond
MDI bonding is more water-resistant than typical retail particle board.
E0 health grade
Luxfit specifies E0 for particle boards; flagship builds use ENF-grade boards (≤0.025 mg/m³).
Smooth for melamine
A flat, even face for melamine finishes in solid colours, wood-grains and textures.
Right board for each part
Low-density board for back panels and screens, high density for doors, plywood where loads are heavy.
Density matters
Choose the right density
Not every part needs the same board. We match density to the job.
Low density · ≤600 kg/m³
Back panels & screens
For back panels, decorative screens and weight-sensitive parts: the economy entry.
High density · 700–800 kg/m³
Tall wardrobe doors
For floor-to-ceiling wardrobe doors up to 2.7 m: stays straight, no “internal memory”, MDI bond.
For heavy loads
11-layer plywood
High-density particle board wins on staying straight; 11-layer plywood still wins on load (granite counters, heavy shelves).
Plywood cabinetsDesign Gallery
Kitchens & wardrobes on engineered cores
Each design visual opens in our Design Gallery with its layout, finishes and key features.
Specification
Particle board cabinet specification
Typical specification
- Carcase
- E0 particle board
- Tall doors
- High-density particle board, 700–800 kg/m³, up to 2.7 m
- Back panels
- Low-density board (≤600 kg/m³) where weight matters
- Bond
- MDI adhesive
- Finish
- Melamine (Y, YU, BK) and other finish series
- Machining
- CNC to 0.1 mm tolerance
Compare
- vs 11-layer plywood
- Plywood wins on load: sink runs, wet zones, stone tops, heavy shelves
- vs MDF
- MDF is the smooth board for lacquer and CNC-carved doors
- vs retail particle board
- MDI bond is more water-resistant
Indicative budgets
- Indicative kitchen budgets: about UGX 5–12 million (small), 12–25 million (medium) and 25–50 million (large), including cabinetry materials and countertops; appliances are not included. Final quotes depend on layout, finishes and site conditions after measurement.
Cabinet quality control system
Quality control, checked at every stage
Every Luxfit order goes through one quality system, run by Luxfit and our manufacturing partners. Your confirmed drawings feed the production system directly, every panel is labelled and tracked from cutting to packing, and checks are built into each stage rather than left to the end.
- 01
Site measure & confirmed drawings
Our technical team measures on site. Production only starts after you approve the 2D drawings and 3D mock-ups.
- 02
Incoming material inspection
Boards, edge banding and finishes are checked against your specification (board grade, E0 or E1, and finish code) before cutting.
- 03
Smart cutting & edge banding
Production data goes straight from your drawings to the CNC line. Panels are cut to 0.1 mm tolerance and each one gets a QR-coded label.
- 04
Drilling & sorting checks
Each panel is scanned before drilling, so holes follow the drawing and a wrong size or position is flagged. Sorting confirms no part is missing.
- 05
Finished-panel inspection
Inspectors check panel sizes, edge banding, colour and drill positions, then clean every panel so no dust remains before packing.
- 06
Hardware checks
Hinges, runners and fittings are picked by type and quantity for your order, then scanned and photo-checked.
- 07
Packing & dispatch
Packages are scanned to confirm quantities, clearly labelled and tracked in the warehouse until loading.
- 08
Fitting to your drawings
After shipping and Uganda clearance, our team fits your cabinets on site to your confirmed drawings.
Testing standards
Standards we build to
- Formaldehyde
- E0 particle board · E1 11-layer plywood · ENF-grade (≤0.025 mg/m³) on flagship builds
- Adhesive
- MDI medical-grade adhesive: waterproof, no toxic glues
- Machining
- CNC to 0.1 mm tolerance
- Lacquer
- Sprayed in layers and baked (oven-cured)
- Coatings
- Anti-fingerprint, scratch-resistant, UV-yellowing resistant (where specified)
- Hardware
- Soft-close hinges and runners; SUS304 stainless steel fittings; runners and lift mechanisms cycle-tested
- Order accuracy
- QR-coded panels scanned at cutting, drilling, sorting and packing
Board grades, finish codes and hardware are confirmed on your quotation.
Premium cabinets quality assurance
Quality partners behind every Luxfit cabinet
We work with established manufacturing and hardware partners and specify each component by use. The options below are confirmed on your quotation.
Partner factory
Automated production line
CNC cutting, edge banding and drilling on an automated line, for consistent quality and efficient production.
Hardware partner
Blum hinges & runners
Our premium hardware option: smooth, quiet soft-close movement for doors and drawers.
Hardware partner
DTC soft-close hinges
Our standard soft-closing hinges for base units, wall units and tall doors.
Storage fittings
Pull-outs & organisers
Pull-out baskets, organiser drawers and soft-close waste sorters (including HIGOLD) in SUS304 stainless steel and nano-coated aluminium.
Finish
Baked lacquer
L-code lacquer is sprayed in layers and oven-baked, like the paint on premium cars, for a smooth, deep, durable colour.
Boards
Healthier board system
E0 particle board, E1 11-layer plywood and ENF-grade flagship boards, bonded with MDI adhesive.
How it works
How it works: from floor plan to fitting
Payment follows 10% before 2D/3D → 40% before production → 40% before Uganda clearance → 10% after fitting. Full stages are in our guide to lead time for Kampala kitchens and wardrobes.
- 01
Share your plan
Send your inquiry with a floor plan or photos to our sales team.
- 02
Site measure
Our technical team measures on site so the drawings match the real space.
- 03
2D & 3D design
After the 10% design deposit you receive 2D drawings and 3D mock-ups, with three revisions included.
- 04
Production
You confirm the design and pay 40% before production. Production takes about 20–40 days.
- 05
Shipping & clearance
Shipping takes about 28–40 days. 40% is due before Uganda clearance.
- 06
Fitting
Our team fits your cabinets on site. The final 10% is paid after fitting.
Explore
More cabinet materials & finishes
FAQ
Particle board cabinets: frequently asked questions
What is particle board?
Particle board is Luxfit’s engineered particle board. The high-density grade (700–800 kg/m³) is made for large wardrobe doors: it stays flat, has no “internal memory” and supports floor-to-ceiling doors up to 2.7 m.
Is particle board strong enough for kitchens?
Yes, for carcases and wall units where it is specified. For sink runs, wet zones and stone countertop loads we specify E1 11-layer plywood, which wins on load.
Does particle board handle moisture?
Our boards are bonded with MDI adhesive, which is more water-resistant than typical retail particle board. Wet zones still get the 11-layer plywood core.
Which grade is your particle board?
Luxfit specifies E0 for particle boards. Flagship builds use ENF-grade boards (≤0.025 mg/m³). See ENF vs E1.
How long does it take and how does payment work?
After you confirm the drawings, production takes about 20–40 days and shipping about 28–40 days, followed by Uganda clearance and fitting on site. Payment is 10% before the 2D and 3D drawings, 40% before production, 40% before Uganda clearance and 10% after fitting.
Can I see samples before I decide?
Yes. Browse finishes and 360° room views in our Design Gallery, then compare the physical samples at our Kampala showroom, Monday to Saturday 08:30–18:00 (National Cleaning Day, the last Saturday of the month: 11:00–19:00; Sunday: VIP by appointment).
Start your project
Plan your cabinets with Luxfit
Send your floor plan or photos and we will propose the right board for each part of your kitchen or wardrobe.
Showroom
Visit our Kampala showroom
See cores, finishes and tall samples in person.
- Mon–Sat
- 08:30–18:00
- National Cleaning Day
- Last Saturday of the month, 11:00–19:00
- Sunday
- VIP by appointment
- Phone
- +256 393 102 850
+256 793 179 034